Devine Color Luscious Trim 3450 Series


	www.millerpaint.com
	1-800-852-3254
	Devine Color
	Luscious Trim 3450 Series
	VOC Compliant
	High Hide Formula

Bases Available:	3450 White	3456 Accent	3458 Neutral
Bases Available:

Devine Color Luscious Trim Interior Paint is a superior quality acrylic architectural coating developed and manufactured exclusively by Miller Paint Company. This unique product is easy to apply with low splatter, excellent flow and leveling qualities. Ideal for hard use residential and commercial kitchens, bathrooms and trim.

Color:	Over 115 designer colors

Finish:	Luscious trim finish

Gloss:	30.0-35.0 @ 60°
	65.0-70.0 @ 85°

Density:	10.81# per gallon

Clean-Up:	Mild soap and water

VOC:	50 gm/liter minus water

Solids:	Weight Volume	52.50% 38.25%

Flash Point:	N/A

Coverage:	215-425 sq. ft. per gallon. Coverage depends of profile and porosity of surface.

Theoretical Coverage:	426 sq. ft. @ 1.5 dry mils

Dry Time:	One to two hours to touch @ 70°F and 50% relative humidity. Four to eight hours to recoat @ 70°F and 50% relative humidity.

Application:	Brush, roll or spray. Spraying and backrolling recommended on new flat work. Do not apply at temperatures below 45°F. Keep product from freezing
	Rev 3/09

Interior Luscious Trim offers exceptional hide, high build, odorless, stain resistant and excellent touch-up. The finish is durable and washable providing a uniquely soft appearance. This product features a strong and durable finish. Canopy is available in the complete Devine Color Palette.

Devine Color Luscious can be applied at a rate of 215 sq. ft. per gallon to yield a 3 mil dry film thickness in one application.

100% Acrylic
Titanium dioxide & extender pigments
Contains no lead or mercury
VOC compliant

Surfaces must be sound, dry and clean. Remove previous coatings that have poor adhesion. Wash areas where mold and mildew are present. Remove all dirt, oil, grease, wax and/or other contaminant. Repair cracks and fill voids. De-gloss shiny surfaces by lightly sanding. Clean and prime all bare metal surfaces with an appropriate primer. Prime areas as needed. Test for adhesion and compatibility with existing finishes.

Never pour leftover coating down any sink or drain—use up material on the job or seal can and store safely for future use. Do not incinerate closed containers. For specific disposal or recycle guidelines, contact your local waste management agency or district. Always attempt to recycle whenever possible.

Limited Warranty: Miller Paint Company, Inc. warrants to the purchaser that this product will provide satisfactory performance when applied according to label directions. If this product does not perform to specifications, return unused portion along with sales receipt to place of purchase. As the sole remedy to purchaser, dealer will, at its option: provide additional product to correct affected areas, replace with product of equal value or refund the purchase price paid for this paint product. Failures caused by poor surface preparation, improper application or a breakdown of the underlying surface or previous paint film are not covered by this warranty. THIS WARRANTY SPECIFICALLY EXCLUDES LABOR OR COST OF LABOR OR INCIDENTAL OR CONSEQUENTIAL DAMAGES ASSOCIATED WITH THE USE OF THIS PRODUCT.

WARNING! If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

Specification figures should be taken as accurate for products being produced at the time of publication in untinted white bases only. Formulation improvements may be made from time to time that may affect these figures to some degree. Also, manufacturing tolerances of ±2% are considered acceptable. Whenever a change is made that the Manufacturer considers substantial, the Product Analysis will be revised.