Devine Color Powder Wall Finish #3150


	www.millerpaint.com
	1-800-852-3254
	Devine Color
	Powder Series 3150
	VOC Compliant
	High Hide Formula

Bases Available:	3150 - White 3156 - Accent 3158 - Neutral
Bases Available:

Devine Color Powder Wall Finish Interior Paint is a superior quality acrylic archtitectural coating developed and manufactured exclusively by Miller Paint Company. This unique product is easy to apply with low splatter, excellent flow and leveling qualities.

Color:	Over 115 Designer Colors

Finish:	Matte Flat Finish

Gloss:	2.5-3.5 @60°
	2.5-5.0 @85°

Density:	12.34# per gallon

Clean-Up:	Warm Soapy Water

VOC:	49 gm/liter

Volume Solids:	44.1%

Flash Point:	N/A

Coverage:	250 - 490 sq. ft. per gallon. Coverage depends on porosity and profile of surface.

Theoretical Coverage:	494 sq. ft. @ 1.5 dry mils

Dry Time:	One hour to touch, 6 hours to recoat @70°F and 50%.

Application:	Brush, roll or spray. Spraying and backrolling recommended on new flat work. Do not apply at temperatures below 45°F. Keep product from freezing.
	Rev 3/09

The matte flat finish utilizes a unique copolymer blend latex that is low in odor, high hiding, stain-resistant, and washable with warm water and soap. Low splatter, excellent flow and leveling, and durability combine to present the rich soft look and feel of the Devine Color palette.

Devine Color Powder Wall Finish can be applied at a rate of 250 sq. ft. per gallon to yield a 3 mil dry film thickness in one application.

Acrylic Copolymer Blend latex
Titanium dioxide & extender pigments
Contains no lead or mercury
VOC compliant

Surfaces must be sound, dry and clean. Remove previous coatings that have poor adhesion. Wash areas where mold and mildew are present. Remove all dirt, oil, grease, wax and/or other contaminant. Repair cracks and fill voids. De-gloss shiny surfaces by lightly sanding. Clean and prime all bare metal surfaces with an appropriate primer. Prime areas as needed. Test for adhesion and compatibility with existing finishes.

Never pour leftover coating down any sink or drain—use up material on the job or seal can and store safely for future use. Do not incinerate closed containers. For specific disposal or recycle guidelines, contact your local waste management agency or district. Always attempt to recycle whenever possible.

Limited Warranty: Miller Paint Company, Inc. warrants to the purchaser that this product will provide satisfactory performance when applied according to label directions. If this product does not perform to specifications, return unused portion along with sales receipt to place of purchase. As the sole remedy to purchaser, dealer will, at its option: provide additional product to correct affected areas, replace with product of equal value or refund the purchase price paid for this paint product. Failures caused by poor surface preparation, improper application or a breakdown of the underlying surface or previous paint film are not covered by this warranty. THIS WARRANTY SPECIFICALLY EXCLUDES LABOR OR COST OF LABOR OR INCIDENTAL OR CONSEQUENTIAL DAMAGES ASSOCIATED WITH THE USE OF THIS PRODUCT.

WARNING! If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

Specification figures should be taken as accurate for products being produced at the time of publication in untinted white bases only. Formulation improvements may be made from time to time that may affect these figures to some degree. Also, manufacturing tolerances of ±2% are considered acceptable. Whenever a change is made that the Manufacturer considers substantial, the Product Analysis will be revised.