www.millerpaint.com
1-800-852-3254
Acro® Pure
Interior Satin 1450 Series
Ultra-Low-VOC
Applies to LEED Credits MR 5.1/5.2, EQ 4.2 and/or ID2.1; Green Seal™  (GS-11) Certified MPI Approved
Product #145
Bases Available: 1450 White 1482 Medium 1486 Accent
1488 Neutral
Product Description     Specifications
ACRO PURE is an ultra-low-VOC interior acrylic latex finish designed for application to the interior walls in residential, commercial, institutional and industrial environments. Recommended for new or previously painted interior wallboard, plaster, masonry or previously painted or primed metal or wood substrates.

    
Color: Full range
Finish: Satin
Gloss: 10-20% @ 60°
Density: 10.72# per gallon
Clean-Up: Mild soap and water
VOC: <6 grams/liter minus water.  The addition of colorant may add VOCs.
Volume
Solids:		 34%
Flash Point: N/A
Coverage: 350-400 sq. ft. per gallon @ 1.5 dry mils ideal film thickness.  Two coats recommended.  Coverage depends on porosity and profile of surface. We believe in responsible building practices and encourage you to only buy the amount of paint needed for your project.

Theoretical
Coverage:

 381 sq. ft. @ 1.5 dry mils
Dry Time: One hour to touch @ 70°F and 50% relative humidity. Three hours to recoat @ 70°F and 50% relative humidity.
Application: Brush, roll or spray. Spraying and backrolling recommended on new flat work. Do not apply at temperatures below 45°F. Keep product from freezing. Use with proper ventillation.

Rev 6/09
Features
ACRO PURE is a low odor, ultra-low-VOC, Green Seal™ Certified, environmentally responsible interior acrylic latex satin finish.  ACRO PURE is formulated to produce excellent application properties and durability.  ACRO PURE is enhanced with antimicrobial protection to inhibit the growth of odor causing mold and mildew bacteria on the dried paint surface.
Composition

Quality acrylic resin
Titanium dioxide
Extender pigments
Antimicrobial protection





 

Surface Preparation
Surfaces must be sound, dry and clean. Remove previous coatings that have poor adhesion. Wash areas where mold and mildew are present. Remove all dirt, oil, grease, wax and/or other contaminant. Repair cracks and fill voids. De-gloss shiny surfaces by lightly sanding. Clean and prime all bare metal surfaces with an appropriate primer. Prime areas as needed. Test for adhesion and compatibility with existing finishes.
Disposal
Never pour leftover coating down any sink or drain—use up material on the job or seal can and store safely for future use. Do not incinerate closed containers. For specific disposal guidelines or recycling opportunities for leftover product and packaging, contact your local waste management agency or district. Always attempt to recycle whenever possible.
Warranty
Limited Warranty: Miller Paint Company, Inc. warrants to the purchaser that this product will provide satisfactory performance when applied according to label directions. If this product does not perform to specifications, return unused portion along with sales receipt to place of purchase. As the sole remedy to purchaser, dealer will, at its option: provide additional product to correct affected areas, replace with product of equal value or refund the purchase price paid for this paint product. Failures caused by poor surface preparation, improper application or a breakdown of the underlying surface or previous paint film are not covered by this warranty. THIS WARRANTY SPECIFICALLY EXCLUDES LABOR OR COST OF LABOR OR INCIDENTAL OR CONSEQUENTIAL DAMAGES ASSOCIATED WITH THE USE OF THIS PRODUCT.

Possible Existing Lead Warning
WARNING! If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
Specification figures should be taken as accurate for products being produced at the time of publication in untinted white bases only. Formulation improvements may be made from time to time that may affect these figures to some degree. Also, manufacturing tolerances of ±2% are considered acceptable. Whenever a change is made that the Manufacturer considers substantial, the Product Analysis will be revised.